RCOPWORLD
Torson Differential Arrma Fsr Km ZDRACING 1/7 1/8 Rc Car Universal Op
Torson Differential Arrma Fsr Km ZDRACING 1/7 1/8 Rc Car Universal Op
Regula prezo
$108.00 USD
Regula prezo
$130.00 USD
Venda prezo
$108.00 USD
Unueca prezo
per
Impostoj inkluzivitaj.
Sendado kalkulita ĉe la kaso.
Ne eblis ŝargi la haveblecon de ŝarĝo
Note: If you want to go back to the original car to pick up the cup, please be sure to remove the center positioning pin, otherwise the large (umbrella) teeth may not cover it.
Torson is not suitable or recommended to play flying slope, head up and somersault, because the internal gear modulus is small, these three games have the risk of sweeping teeth.
brand
Model
ARRMA 1/7 rc car (Non-spline drive)
At present, the measured and available models include Typhoon, Firebird, Cross-Border, F1 (medium difference is not applicable), Mojave 6s. The front and rear difference should be connected to the original car with the large umbrella teeth and the original car on the same side. EXB models can only be directly installed with medium difference.
KMOne, two and three generations of tension
The front and rear difference only needs to be replaced with the large umbrella teeth, and the Torson cup and center positioning pin must be retained. The first generation of medium difference direct installation, the second and third generations, the difference is not suitable for the Torson due to the transfer box, or the second generation of medium difference bracket and front drive shaft are used.
XRAY
GT2021 325mm wheelbase
The front and rear differences only need to be replaced with large umbrella teeth, and the Torson cup and center positioning pin can be retained. The medium difference needs to be replaced with a long cup to be used. The front, middle and rear differences can be used with the original large (umbrella teeth straight).
Torson is not suitable or recommended to play flying slope, head up and somersault, because the internal gear modulus is small, these three games have the risk of sweeping teeth.
brand
Model
ARRMA 1/7 rc car (Non-spline drive)
At present, the measured and available models include Typhoon, Firebird, Cross-Border, F1 (medium difference is not applicable), Mojave 6s. The front and rear difference should be connected to the original car with the large umbrella teeth and the original car on the same side. EXB models can only be directly installed with medium difference.
KMOne, two and three generations of tension
The front and rear difference only needs to be replaced with the large umbrella teeth, and the Torson cup and center positioning pin must be retained. The first generation of medium difference direct installation, the second and third generations, the difference is not suitable for the Torson due to the transfer box, or the second generation of medium difference bracket and front drive shaft are used.
XRAY
GT2021 325mm wheelbase
The front and rear differences only need to be replaced with large umbrella teeth, and the Torson cup and center positioning pin can be retained. The medium difference needs to be replaced with a long cup to be used. The front, middle and rear differences can be used with the original large (umbrella teeth straight).
HOBAO H9E, 8SC, VS, VTE
HPI V orza, apache
Kyosho GT generation two generation, MP9, MP10
FSR Shark, Tank, Astro Boy, Cheetah 1/8 Universal
zdracing DBX-07,EX-07
Medium difference direct installation. The front and rear difference only needs to replace the large umbrella teeth, and the Torson cup and center positioning pin must be retained.
The front, middle and rear differences only need to replace the large (umbrella) teeth, and the Torson cup and center positioning pin can be retained.
The front, middle and rear differences can be used. The original large (umbrella) tooth straight installation
The front, middle and rear differences can be used. The original large (umbrella) tooth straight installation
HPI V orza, apache
Kyosho GT generation two generation, MP9, MP10
FSR Shark, Tank, Astro Boy, Cheetah 1/8 Universal
zdracing DBX-07,EX-07
Medium difference direct installation. The front and rear difference only needs to replace the large umbrella teeth, and the Torson cup and center positioning pin must be retained.
The front, middle and rear differences only need to replace the large (umbrella) teeth, and the Torson cup and center positioning pin can be retained.
The front, middle and rear differences can be used. The original large (umbrella) tooth straight installation
The front, middle and rear differences can be used. The original large (umbrella) tooth straight installation
